TM-5-4320-240-15

• OPERATOR, ORGANIZATIONAL, DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT MAINTENANCE MANUAL PUMP, CETRIFUGAL, G.E.D., SKID MOUNTED, 6 IN., 1120 GPM
• SAFETY PRECAUTIONS
• Operator, Organizational, Direct Support, General Support, and Depot Maintenance Manual is changed as follows
• Operator, Organizational, Direct Support, General Support, and Depot Maintenance Manual is changed as follows
• Explanation of Columns
• Section III. BASIC ISSUE ITEMS
• Section II. EXPENDABLE SUPPLIES AND MATERIALS LIST
• Operator, Organizational, Direct Support, General Support, and Depot Maintenance Manual is changed as follows
• Table of Contents
• CHAPTER 1. INTRODUCTION
• Figure 1-1. Centrifugal pump, right front view, wit panels off.
• Figure 1-2. Centrifugal pump, left rear view, with panels off
• Figure 1-3. Wiring diagram.
• Figure 1-4. Base plan.
• Difference in Models
• CHAPTER 2. INSTALLATION AND OPERATION INSTRUCTIONS
• Figure 2-1. Areas of pump from which packing must be removed.
• Figure 2-2. Areas of pump requiring inspection.
• Figure 2-3. Areas of pump requiring service.
• Section II. MOVEMENT TO NEW WORKSITE
• Figure 2-4. Controls and instruments.
• Section IV. OPERATION OF EQUIPMENT
• Figure 2-5. Starting procedure.
• Starting
• Operation Under Usual Conditions
• Operation in Extreme Heat
• Table 2-2. Pump Efficiency at Varying Elevations
• CHAPTER 3. OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
• Section III. PREVENTIVE MAINTENANCE SERVICES
• Figure 3-3 (1). Daily preventive maintenance services.
• Daily Preventive Maintenance Services
• Figure 3-4 (1)-Quarterly preventive maintenance services.
• Section IV. OPERATOR AND ORGANIZATIONAL MAINTENANCE
• Figure 3-5. Fuel strainer service.
• Section V. TROUBLESHOOTING
• Engine Misses or Runs Erratically
• Section VI. RADIO INTERFERENCE SUPPRESSION
• Figure 3-9. Fuel pump removal and installation.
• Air Cleaner
• Fuel Tank
• Fuel Lines and Fittings
• Figure 3-17. Fuel lines and fittings.
• Section VIII. ENGINE ELECTRICAL SYSTEM
• Batteries
• Generator
• Figure 3-2I. Generator regulator removal and installation.
• Figure 3-23. Starts motor-exploded view
• Figure 3-24. Magneto adjustment.
• Generator Regulator
• Figure 3-26. Magneto exploded view.
• Magneto
• Section IX. COOLING SYSTEM
• Figure 3-27. Water pump removal and installation.
• Figure 3-8. Thermostat removal and installation .
• Figure -3-30. Reverse flushing radiator.
• Figure 3-31. Reverse flushing engine water jacket.
• Figure 3-32. Coolant piping and hoses.
• Figure 33-3. Oil filter removal and installation.
• Oil Filter
• Figure 3-35. Breather removal and installation.
• Figure --6. Oil lines and fittings.
• Section XI. PUMP ASSEMBLY AND COMPONENTS
• Discharge and Intake Pressure Lines
• Figure S3-9. Pump removal and installation.
• Figure 3-40. Water pump exploded view.
• Section XII. CONTROLS AND INSTRUMENTS
• Intake Pressure Gage
• Ammeter
• Throttle Control
• Figure 3-48. Battery disconnect switch removal and installation.
• Figure 3-49. Choke control removal and installation
• Figure 5-53. Panel light removal and installation.
• Section XII ENGINE
• Muffler and Exhaust Pipe
• Figure 5-7. Muffler guard removal and installation.
• Figure 3-58. Muffler removal and installation.
• Figure 3-59. Manifold removal and installation.
• Figure 3-60. Housing, engine.
• CHAPTER 4. DIRECT AND GENERAL SUPPORT AND DEPOT MAINTENANCE INSTRUCTIONS
• Table 4-1. Repair and Replacement Standards
• Table 4-1. Repair and Replacement Standards-continued
• CHAPTER 5. GENERAL MAINTENANCE INSTRUCTIONS
• Engine Lacks Power
• Section IV. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS OR AUXILLIARIES
• Figure 5-1. Engine assembly and housing removal and installation.
• CHAPTER 6. ENGINE REPAIR INSTRUCTIONS
• Figure 6-1. Governor-exploded view.
• Starting Motor
• Figure 6-3. Starting motor test hook-up.
• Generator Regulator
• Figure 6-5. Generator regulator cutout relay adjustment.
• Figure 6-6. Generator regulate test set-up.
• Water Pump
• Section II. ENGINE COMPONENTS
• Figure 6-9. Rocker Arm assembly--exploded view.
• Figure 6-10. Manifolds-exploded view.
• Valves, Seats, and Guides
• Figure 6-13. Removing valves.
• Oil Pan
• Oil Pump
• Figure 6-17. Oil pan-exploded view.
• Figure 6-19. Crankshaft, pistons, connecting rods, bearings
• Figure 6-20. Fitting Piston
• Figure 6-21. Checking piston ring clearance.
• Crankshaft, Crankshaft Bearings, and Camshaft
• Figure 6-23. Flywheel removal and installation.
• Figure 6-24. Flywheel housing removal and installation.
• Figure 6-25. Checking flywheel housing and flywheel for runout.
• Engine Block and Cylinder Sleeve
• Figure 6-27. Gear cover removal and installation.
• Figure 6-28. Front seal removal and installation.
• Figure 6-1. Crankshaft gear removal and installation.
• Figure 6-34 Checking gasket crush on sleeve.
• CHAPTER 7. PUMP REPAIR INSTRUCTIONS
• CHAPTER 8. SKID BASE AND RELATED PARTS REPAIR INSTRUCTIONS
• Figure 8-1. Skid base.
• APPENDIX A. REFERENCES
• APPENDIX B. BASIC ISSUE ITEMS LIST
• Section II. BASIC ISSUE ITEMS
• Section III. MAINTENANCE AND OPERATING SUPPLIES
• APPENDIX C. MAINTENANCE ALLOCATION CHART
• Explanation of Columns in Section III
• Section III. REMARKS
• INDEX
• INDEX-continued
• INDEX-continued
• INDEX-continued
• TM-5-4320-240-15
• Shared Top Border
• Blank Page
• Distribution
• Shared Bottom Border
• DISTRIBUTION
• Distribution
• Shared Left Border
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS

Privacy Statement - Press Release - Copyright Information. - Contact Us