Special Information - TM-5-4320-259-20P0010

Code

Explanation

allowance columns. Items authorized for use as

required but not for initial stockage are identified

level. When supply considerations dictate, some

of these repair parts may be listed for automatic

with an asterisk in the allowance column.

return to supply for depot level repair as set

(2) The quantitative allowances for

forth in AR 710-50. When so listed, they will be

organizational level of maintenance represents one

replaced by supply on an exchange basis.

initial prescribed load for a 15-day period for the

Repair parts, Special Tools, Test Equipment and

assemblies which are economically reparable at

number of equipments supported. Units and

DSU and GSU activities and which normally

o r g a n i z a t i o n s a u t h o r i z e d additional prescribed

are furnished by supply on an exchange basis.

loads will multiply the number of prescribed loads

When items are determined by a GSU to be

authorized by the quantity of repair parts reflected

uneconomically reparable, they will be

in the density column applicable to the number of

evacuated to a depot for evaluation and analysis

before final disposition.

i t e m s supported to obtain the total quantity of

High dollar value recoverable Repair parts,

r e p a i r parts authorized.

Special Tools and Test Equipment which are

( 3 ) Organizational units providing main-

subject to special handling and are issued on an

t e n a n c e for more than 100 of these equipments

exchange basis. Such items will be repaired or

shall determine the total quantity of parts required

o v e r h a u l e d at depot maintenance activities

only. No repair may be accomplished at lower

by converting the equipment quantity to a decimal

levels.

factor by placing a decimal point before the next to

Repair parts, Special Tool S and Test Equipment

last digit of the number to indicate hundredths, and

specifically selected for salvage by reclamation

multiplying the decimal factor by the parts quantity

units because of precious metal content, critical

authorized in the 51-100 allowance column.

materials, high dollar value or reusable casings

or castings.

Example, authorized allowance for 51-100

equipments is 40; for 150 equipments multiply 40

b. Federal Stock Number, Column (1) o f

by 1.50 or 60 parts required.

Section II and Column (2) of Section III. This

(4) Subsequent changes to allowances will be

column i n d i c a t e s t h e F e d e r a l s t o c k n u m b e r

limited as follows: No change in the range of items

assigned to the item and will be used for

i s authorized. If additional items are considered

requisitioning purposes.

n e c e s s a r y , recommendation should be forwarded

c. Description, Column (2) of Section II and

t o U.S. Army Mobility Equipment command for

Column (3) of Section III. This column indicates

e x c e p t i o n or revision t o t h e a l l o w a n c e l i s t .

t h e F e d e r a l i t e m n a m e a n d a n y additional

Revisions to the range of items authorized will be

description of the item required. A part number or

m a d e by this Command based upon engineering

o t h e r reference number is followed by the ap-

experience, demand data, or TAERS information.

plicable five-digit Federal supply code for

g. Illustration, Column (7) of Section III. This

manufacturers in parentheses. Repair parts

column is divided as follows:

quantities included in the kits, sets, and assemblies

(1) Figure number, column (7) (a). Indicates

are shown in front of the repair part name. Material

the figure number of the illustration in which the

r e q u i r e d for manufacture or fabrication is iden-

item is shown.

tified.

(2) Item number, column (7) (b). Indicates

d. Unit of Measure (U/M), Column (4) of

the callout number used to reference the item in the

Section III. A 2-character alphabetic abbreviation

illustration.

indicating the amount or quantity of the item upon

which the allowances are based, e.g. ft, ea, pr, etc.

4. Special Information

e. Quantity Incorporated in Unit, C o l u m n ( 5 ) o f

a. Repair parts mortality has been based on

Section III. This column indicates the quantity of

1,000 hours of operation per year.

the item used in the assembly group. A "V" a p -

b. Parts which require manufacture or assembly

pearing in this column in lieu of a quantity in-

at a category higher than that authorized for in-

dicates that a definite quantity cannot be indicated

stallation will indicate in the source column the

(e.g. shims, spacers, etc.).

higher category.

f. 1 5 - D a y

Organizational

Maintenance

c. The following publications pertain to the

Allowance, Column (3) of Section II and Column

pumping assembly and its components:

(6) of Section III.

TM 5-4320-259-12

O p e r a t o r and Organiza-

(1) The allowance columns are divided into

tional

Maintenance

f o u r subcolumns. Indicated in each subcolumn

Manual

opposite the first appearance of each item is the

TM 5-4320-259-34

Direct Support and Gen-

total quantity of items authorized for the number of

e r a l Support Mainte-

equipments supported. Subsequent appearances of

nance Manual

the same item will have the letters "REF" in the