 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 INTRODUCTION
Explanation
Code
Scope
1.
P2
Repair
Parts,
Special
Tools
and
Test
Equip-
This manual lists repair parts required for the
ment
which
are
procured
and
stocked
for
performance of organizational, direct support
purposes
because
the
combat
or
military
essentiality
of
the
end
item
dic-
and general support maintenance of the recipro-
tates
that
a
minimum
quantity
be
available,
c a t i n g pump.
in
the
supply
system.
M
2.
General
Repair
Parts,
Special
Tools
and
Test
Equip-
ment
which
are
not
procured
or
stocked,
as
a. This Repair Parts List is divided into the
such,
in
the
supply
system
but
are
to
be
f o l l o w i n g sections:
manufactured
at
indicated
maintenance
b. Prescribed Load Allowance (PLA)--Sec-
levels.
tion II. A composite listing of repair parts hav-
A
Assemblies
which
are
not
procured
or
stocked
i n g quantitative allowances for initial stockage
as
such,
but
are
made
up
of
two
or
more
at the organizational level.
units.
Such
component
units
carry
in-
dividual
stock
numbers
and
descriptions,
are
procured
and
stocked
separately
and
pair parts authorized for the performance of
can
be
assembled
to
form
the
required
as-
maintenance at the organizational level in figure
sembly
at
indicated
maintenance
categor-
and item number sequence.
ies.
d. Special Tools, Test, and Support Equipment
X
Parts
and
assemblies
that
are
not
procured
--Section IV. (Not Applicable).
or
stocked
because
the
failure
rate
is
nor-
mally
below
that
of
the
applicable
end
item
of
component.
The
failure
of
such
part
or
p a r t s authorized for the performance of mainte-
assembly
should
result
in
retirement
of
the
nance at the direct support and general support
end
item
from
the
support
system.
level in figure and item number sequence.
X1
Repair
Parts
which
are
not
procured
or
f. Special Tools, Test, and Support Equipment
stocked.
The
requirement
for
such
items
S e c t i o n VI. ( N o t A p p l i c a b l e ) .
will
be
filled
by
the
next
higher
assembly
or
component.
g. Federal Stock Number and Reference
X2
Repair
Parts,
Special
Tools,
and
Test
Equip-
ment
which
are
not
stocked
and
have
no
stock numbers in ascending numerical sequence,
foreseen
mortality.
The
indicated
mainte-
followed by a list of reference numbers appearing
nance
category
requiring
such
repair
parts
i n a l l t h e l i s t i n g s , i n ascending alphanumeric
will
attempt
to
obtain
the
parts
through
sequence, c r o s s - r e f e r e n c e d t o t h e i l l u s t r a t i o n
cannibalization
or
salvage,
the
item
may
be
f i g u r e number and item number.
requisitioned
with
exception
data,
from
the
end
item
manager,
for
immediate
use.
3.
Explanation of Columns
G
Major
assemblies
that
are
procured
with
The following provides an explanation of col-
PEMA
funds
for
initial
issue
only
as
ex-
change
assemblies
at
DSU
and
GSU
level.
u m n s in the tabular lists in sections II through
These
assemblies
will
not
be
stocked
above
V:
the
DS
and
GS
level
or
returned
to
de-
a. Source, Maintenance,
and
Recoverability
pot
supply
level.
C o d e s (SMR).
Note. Cannibalization
or
salvage
may
be
(1) Source code indicates the selection sta-
used
as
a
source
of
supply
for
any
items
tus and source for the listed item. Source codes
S Ou
rce
coded
above
except
those
coded
X1
used are:
and
aircraft,
support
items
as
restricted
by
AR
700-42.
Code
Explanation
(2) Maintenance code indicates the lowest
P
Repair
Parts,
Special
Tools
and
Test
Equip-
category of maintenance authorized to install the
ment
supplied
from
the
G S A DSA,
or
Army
listed item. The maintenance level codes are:
supply
system,
and
authorized
for
use
at
indicated
maintenance
categories.
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals