|
| |
- OPERATOR, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL PUMPING ASSEMBLY, FLAMMABLE LIQUID BULK TRANSFER, GED, 350 GPM CAPACITY, 275 FEET TOTAL HEAD, WHEEL MOUNTED
- WARNING
- Operator, Organizational, Direct Support and General Support Maintenance Manual is changed as follows
- Operator, Organizational, Direct Support and General Support Maintenance Manual is changed as follows
- Operator, Organizational, Direct Support and General Support Maintenance Manual is changed as follows
- Operator, Organizational, Direct Support and General Support Maintenance Manual is changed as follows
- Table of Contents
- LIST OF ILLUSTRATIONS
- LIST OF ILLUSTRATIONS-continued
- CHAPTER 1. INTRODUCTION
- Figure 1-1. Pumping assembly, right front, three-quarter view
- Figure 1-2. Pumping assembly Left rear, three-quarter view.
- Identification and Tabulated Data
- Wiring Diagram
- Difference in Models
- CHAPTER 2. OPERATING INSTRUCTIONS
- Starter Switch
- Figure 2-3. Right side view of pumping assembly showing controls.
- Before Operation Services
- Operation.
- Section II. OPERATION UNDER UNUSUAL CONDITIONS
- Sandy or Dusty Conditions.
- CHAPTER 3. OPERATOR'S MAINTENANCE INSTRUCTIONS
- Figure 3-1. Lubrication order.
- Detailed Lubrication Information.
- Table 3-1. Operator/Crew Preventive Maintenance Checks and Services
- Table 3-1. Operator/Crew Preventive Maintenance Checks and Services (cont)
- Table 3-1. Operator/Crew Preventive Maintenance Checks and Services (cont)
- Operator/Crew Maintenance Troubleshooting
- Table 3-2. Troubleshooting -- Continued
- Table 3-2. Troubleshooting -- Continued
- Figure 3-4. Air cleaner.
- PUMP ASSEMBLY
- Fuel System.
- Electrical System
- Suction Strainer.
- Figure 3-8. Suction strainer.
- CHAPTER 4. ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
- Section II. MOVEMENT TO A NEW WORKSITE
- Table 4-1. Organizational Preventive Maintenance Checks and Services
- Section VI. TROUBLESHOOTING
- Figure 4.1. Battery and battery box.
- ENGINE-continued
- Figure 4-2. Starting motor.
- ENGINE CRANKS BUT FAILS TO START (NO SPARK).
- Figure 4-3. Ignition system
- Figure 44. Magneto-to-spark plug connections.
- Figure 4-.5. Magneto.
- ENGINE-continued
- Figure 4-6. Magneto timing.
- ENGINE CRANKS BUT FAILS TO START (GOOD SPARK)
- Figure 4-7. Fuel pump.
- Figure 4-3. Fuel strainer.
- ENGINE RUNS BUT LACKS POWER
- Figure 4-9. Suction piping assembly.
- PUMP-continued
- Figure 4-10. Air eliminator assembly
- Section VII. RADIO INTERFERENCE SUPPRESSION
- Section IX. MAINTENANCE AND MUFFLER MANIFOLD
- Figure 4-12. Muffler
- Figure 4-13. Manifold assembly and carburetor.
- Section X. MAINTENANCE OF FUEL SYSTEM
- Figure 4-14. Air cleaner and piping.
- Fuel Tank, Lines, and Fittings.
- Figure 4-16. Fuel strainer.
- Figure 4-17. Fuel pump.
- Carburetor.
- Figure 4-19. Carburetor removal.
- Governor Adjustment.
- Battery, Battery Box, and Leads
- Figure 421. Battery and battery box
- Magneto, Spark Plugs, and Cables.
- Figure 4-22. Magneto breaker point removal.
- Figure 4-23. Magneto removal.
- Installation adn Magneto Timing
- Figure 4-25. Magneto-to-spark plug connections.
- Figure 4-26. Starting motor and brush removal.
- Control Panel and Instruments.
- Figure 4-27. Insrtrument panel and gages
- Section XII. MAINTENANCE OF NON-ELECTRICAL GAGES
- Pump Suction and Discharge and Engine Vacuum Gages, Lines, and Fittings.
- Section XIII. MAINTENANCE OF ENGINE COOLING SYSTEM
- Figure 4-29. Engine air shroud
- Section XIV. MAINTENANCE OF WHEELS AND HUBS
- Figure 4-30. Wheel assembly and hub.
- Section XV. MAINTENANCE OF PUMP
- Figure 4-31. Suction piping and Y strainer.
- Discharge Piping.
- Figure 4-32. Discharge piping
- Section XVI. MAINTENANCE OF ACCESSORY ITEMS
- Figure 4-33. Tool box and reflector
- Cleaning and Inspection
- CHAPTER 5. DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- Figure 5-1. Cylinder head and valve removal.
- Table 5-1. Troubleshooting -- Continued
- Figure 5-3. Pump assembly.
- PUMP-continued
- Section III. GENERAL MAINTENANCE
- Axle Assembly
- CHAPTER 6. REPAIR OF ENGINE
- Section II. ENGINE OVERHAUL AND REPAIR
- Figure 6-1. Governor assembly.
- Figure 6-2. Governor adjustment
- Flywheel
- Figure 6-5. Gear cover and idler shaft.
- Oil Pan and Oil Pump.
- Figure 6-7. Oil pan removal.
- Crankshaft, Piston, and Connecting Rods
- Disassembly
- Figure 6-10. Piston ring placement.
- Cylinder Block and Valves.
- Cleaning and Inspection
- Camshaft and Crankcase.
- Figure 6-12. Crankcase and camshaft
- Flywheel Alternator.
- Removal.
- Figure 6-13. Flywheel alternator.
- CHAPTER 7. REPAIR OF CENTRIFUGAL PUMP
- Figure 7-1. Pump assembly.
- Figure 7-2. Pump tolerances and wear limits.
- Reassembly and Installation-continued
- CHAPTER 8. REPAIR OF FRAME ASSEMBLY
- Figure 8-1. Axle assembly
- Frame.
- Figure 8-2. Frame assembly
- Cleaning and Inspection.
- APPENDIX A. REFERENCES
- APPENDIX B. MAINTENANCE ALLOCATION CHART
- Section II. MAINTENANCE ALLOCATION CHART
- Section II. MAINTENANCE ALLOCATION CHART-continued
- Section II. MAINTENANCE ALLOCATION CHART-continued
- Section III. TOOL AND TEST EQUIPMENT REQUIREMENTS
- INDEX
- INDEX-continued
- INDEX-continued
- INDEX-continued
- INDEX-continued
- INDEX-continued
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- TM-5-4320-273-14
- Blank Page
- Shared Top Border
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- DISTRIBUTION
- Blank Page
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- Blank Page
- Blank Page
- Blank Page
- Shared Bottom Border
- Blank Page
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- Blank Page
- Shared Left Border
|
Click
here for thousands of PDF manuals