TM-5-4320-248-15

• OPERATOR , ORGANIZATIONAL, DIRECT AND GENERAL SUPPORT AND DEPOT MAINTENANCE MANUAL FUEL SYSTEM, TRANSFER, PORTABLE, PUMP CENTRIFUGAL, 100 GPM; TWO DISCHARGE HOSE ASSEMBLIES; ONE SUCTION HOSE ASSEMBLY; TWO NON-AUTOMATIC NOZZLE ASSEMBLIES; ONE MONITOR GO-NO-GO GAGE, 100 GPM
• SAFETY INSTRUCTIONS
• Operator, Organizational, Direct and General Support and Depot Maintenance Manual is changed as follows
• Figure 13.1. Lubrication order.
• Figure 13.2. Lubrication order (Cont'd).
• APPENDIX A. REFERENCES
• APPENDIX B. COMPONENTS OF END ITEMS LIST
• Section I. INTEGRAL COMPONENTS OF END ITEM
• APPENDIX E. EXPENDABLE SUPPLIES AND MATERIALS LIST
• Operator, Organizational, Direct and General Support and Depot Maintenance Manual is changed as follows
• Operator, Organizational, Direct and General Support and Depot Maintenance Manual is changed as follows
• Section III. ITEMS TROOP INSTALLED OR AUTHORIZED LIST
• Operator, Organizational, Direct and General Support and Depot Maintenance Manual is changed as follows
• Section II. BASIC ISSUE ITEMS
• Table of Contents
• Table of Contents-continued
• Table of Contents-continued
• Table of Contents-continued
• CHAPTER 1. INTRODUCTION
• Monitor, Go-No-Go Gage.
• Section III. SYSTEM TABULATED DATA
• Pump Data.
• FIGURE NO. 1. 114MX1A ASSEMBLY AS PACKAGED
• FIGURE NO. 2. 114MX1A FUEL TRANSFER SYSTEM
• FIGURE NO. 3. 114MX1A - FIELD SET UP
• FIGURE NO. 4. 114MX1A PUMP-ENGINE-MONITOR ASSEMBLY
• FIGURE NO. 5. 114MX1A CARRYING BASKET
• CHAPTER 2 UNPACKAGING AND DEPRESERVATION
• Other Equipment.
• FIGURE NO. 6. SX-1077 ACCESSORY HOSE & NOZZLE PACKAGE
• FIGURE NO. 7. AIR CLEANER ASSEMBLY
• FIGURE NO. 8. OVERPACK KIT K 214-2
• CHAPTER 3. OPERATING INSTRUCTIONS
• Section II. ENGINE ADJUSTMENTS
• Tune Up Specifications.
• Section III. OPERATING INSTRUCTIONS
• Starting a Cold Engine.
• Section IV  TROUBLESHOOTING HINTS
• Engine Functions Properly but Pump Fails to Prime.
• Pump Primes but Fails to Deliver Proper Capacity-continued
• FIGURE NO. 10. CONTROL LOCATION,  ENGINE SX-1086 (Rear View)
• FIGURE NO. 11. CONTROL LOCATION, ENGINE SX-1086 (Front View)
• FIGURE NO. 12. NOZZLE ASSEMBLY SX-931A
• FIGURE NO. 13. PRIMING THE PUMP
• CHAPTER 4 OPERATOR' S MAINTENANCE INSTRUCTIONS
• Section III. STORAGE
• Pump Disassembly-continued
• Section V. REPLACEMENT OF MONITOR ELEMENTS
• CHAPTER 5. MINOR REPAIRS
• SERVICE AND MAINTENANCE DATA FOR 114MX1A PORTABLE FUEL TRANSFER SYSTEM (PUMP-ENGINE-MONITOR)
• Figure 14. Fuel transfer pump assembly.
• K 214-5 FIELD SERVICE KIT FOR MODEL 114MX1A PORTABLE, FUEL TRANSFER SYSTEM
• Replacement of Shaft Seal-Sleeve-Seal Seat
• PUMP SERVICE KIT K214-5
• SERVICE AND MAINTENANCE DATA FOR 3 HP ENGINE COMPONENTS
• Maintenance & Teardown Instructions.
• Check Ignition.
• Equipment. - Effecting Engine Operation.
• Compression.
• FIGURE 16 HEAD TIGHTENING SEQUENCE
• Valve Guides - SX-1086.
• FIGURE 17. VALVE SPRING LOCATION
• FIGURE 18 VALVE SPRING REMOVAL
• To Drive in New Valve Seat Insert.
• Ignition.
• Install Breaker Points.
• FIGURE 23. BREAKER POINT SERVICE
• FIGURE 24 BREAKER POINT ADJUSTMENT
• Adjusting Breaker Point Gap.
• Carburetion.
• Throttle.
• Fuel Pump
• Cylinders.
• To Hone Cylinder.
• Pistons - Rings - Rods.
• Check Connection Rod,
• Assembly Rings to Piston.
• Install Piston and Rod Assembly-continued
• Crankshafts and Camgears.
• Common Specifications for Model SX-1086 Engines:
• Checking Cam Gear.
• FIGURE 27
• Aluminum Engines - Ball Bearing.
• Bearings
• Replacing Magneto Bearing (Aluminum Cylinder Engines )-continued
• Starters.
• FIGURE 28. BLOWER HOUSING & STARTER
• Lubrication.
• Governor.
• TABLE OF TOOLS AND DESCRIPTION
• SERVICE AND MAINTENANCE DATA FOR ACCESSORY HOSE AND NOZZLE PACKAGE
• Figure 29. Discharge hose assembly SX-937.
• FIGURE NO. 31. NOZZLE ASSEMBLY SX-931A
• SERVICE AND MAINTENANCE DATA FOR MONITOR ASSEMBLY (100 GPM GO-NO-GO GAGE)
• FIGURE NO. 32 GAGE ASSEMBLY SX-706
• FIGURE NO. 23. BENDIX GAGE ASSEMBLY
• FIGURE NO. 34. BENDIX GAGE ELEMENT (Exploded View)
• APPENDIX A. BASIC ISSUE ITEMS LIST
• Explanation of Columns in the Tabular List of Maintenance and Operating Supplies Section III
• Section II. BASIC ISSUE ITEMS LIST
• APPENDIX B. MAINTENANCE ALLOCATION CHART
• REBUILD.
• Section II. MAINTENANCE ALLOCATION CHART
• APPENDIX C. LUBRICATION ORDER
• Lubrication Order -- Continued.
• Figure 14. Fuel transfer pump assembly.
• FIGURE NO. 14. FUEL TRANSFER PUMP ASSEMBLY
• FIGURE NO. 29. DISCHARGE HOSE ASSEMBLY SX-937
• FIGURE NO. 30. SUCTION HOSE ASSEMBLY SX-848
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Figure 15. (Not used)
• TM-5-4320-248-15
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Shared Top Border
• Blank Page
• Distribution
• Blank Page
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Blank Page
• Distribution
• Distribution
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Shared Bottom Border
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Blank Page
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Blank Page
• Shared Left Border
• Blank Page

Privacy Statement - Press Release - Copyright Information. - Contact Us