Special Information - TM-5-4320-220-20P0006

TM 5-4320-220-20P

expendable. Recoverability codes are:

the quantity of repair parts reflected in the appropriate density

Code

Explanation

column applicable to the number of items supported to obtain

the total quantity of repair parts authorized.

Applied to repair parts and assemblies

which are economically repairable at

(3) Organizational units providing maintenance

DSU and GSU activities and normally

for more than 100 of these equipments shall determine the

are furnished by supply on an

total quantity of parts required by converting the equipment

exchange basis.

quantity to a decimal factor by placing a decimal point before

the next to last digit of the number to indicate hundredths, and

Applied to high dollar value recoverable

multiplying the decimal factor by the parts quantity authorized

repair parts which are subject to

in the 51-100 allowance column.

Example, authorized

special handling and are issued on an

allowance for 51-100 equipments is 40; for 150 equipments

exchange basis. Such repair parts

multiply 40 by 1.50 or 60 parts required.

normally are repaired or overhauled

at depot maintenance activities.

(4) Subsequent changes to allowances will be

limited as follows: No change in the range of items is

Applied to repair parts specifically

authorized. If additional items are considered necessary.

selected for salvage by reclamation

recommendation should be forwarded to U.S. Army Mobility

units because of precious metal

Equipment Command for exception or revision to the

content, critical materials, high dollar

allowance list. Revisions to the range of items authorized will

value reusable casing or castings.

be made by this Command based upon engineering

experience, demand data, or TAERS information.

(4) This column also lists, below the SMR code,

an index number for each item in ascending numerical

sequence, which is used to locate items in the publication

h. Illustration, Column (8). This column is divided as

when the Federal stock number and/or reference number is

follows:

known.

(1) Figure number column (8a). Indicates the

figure number of the illustration in which the item is shown.

b. Federal Stock Number. This column indicates the

Federal stock number for the item.

(2) Item number, column (8b). Indicates the

callout number used to reference the item in the illustration.

c. Description. This column indicates the Federal item

name and any additional description of the item required. A

4. Special Information

part number or other reference number is followed by the

applicable five digit Federal supply code for manufacturers in

a. Repair parts mortality has been based on 1,000

parentheses. Material required for manufacture or fabrication

hours of operation per year.

is identified.

d. Unit of Issue. This column indicates the unit used as

b. Parts which require manufacture or assembly at a

a basis for issue, e.g., ea., pr, ft, yd, etc.

category higher than that authorized for installation will

indicate in the source column the higher category.

e. Quantity Incorporated in Unit Pack. This column

indicates the actual quantity contained in the unit pack.

c. The following publications pertain to the pump and

its components:

f. Quantity Incorporated in Unit. This column indicates

the quantity of the item used in the functional group.

TM 5-4320 220-15

Operator, organizational,

field and depot

g. Fifteen-Day Organizational Maintenance Allowance,

maintenance manual

Column (4) of Section II arid Column (7) of Section III and IV.

LO 5-4320-220--15

Lubrication order

(1) The allowance columns are divided into four

subcolumns. Indicated in each subcolumn is the quantity of

5. How to Locate Repair Parts

items authorized for the number of equipments supported.

a. When Federal stock number or reference number is

Items authorized for use as required but not for initial

unknown:

stockage are identified with an asterisk in the allowance

(1) First. Using the table of contents, determine

column.

the functional group within which the

(2) The quantitative allowances for organizational

level of maintenance represents one initial prescribed load for

a 15-day period for the number of equipments supported.

Units and organizations authorized additional prescribed loads

will multiply the number of prescribed loads authorized by