|
| |
TM 10-4930-229-12&P
CHAPTER 4
UNIT MAINTENANCE INSTRUCTIONS
Page
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-1
Section I
Repair Parts, Special Tools, Test, Measurement and Diagnostic
Equipment (TMDE) and Support Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-1
Section II
Service Upon Receipt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-1
Section III
Unit Preventive Maintenance Checks and Services (PMCS) . . . . . . . . . . . . . . . . . . . . . ...4-2
Section IV
Unit Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...-.......4-3
Section V
Unit Maintenance Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-6
Section VI
Preparation for Shipment or Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-35
OVERVIEW
This chapter contains unit level maintenance instructions for the FARE. It includes references to the Repair Parts and
Special Tools List in Appendix F, service upon receipt, unit PMCS and unit troubleshooting procedures. It also
includes unit maintenance procedures for the discharge and suction hoses, fittings and adapters, and hose frame
assembly. Refer toTM 5-4930-235-13&P for repair of closed circuit nozzles. Refer to TM 5-4320-256-14&P for
repair of pump assembly. Refer to TM9-2805-257-14 for repair of engine assembly. Refer to TM5-4330-217-12&P
for repair of filter/separator assembly. Refer to TM 10-8110-201-14&P for repair of the drum. Section VI which
describes preparation for storage or shipment, includes procedures for administrative, short term and intermediate
term storage.
Section I. REPAIR PARTS, SPECIAL TOOLS, TEST, MEASUREMENT AND
DIAGNOSTIC EQUIPMENT (TMDE) AND SUPPORT EQUIPMENT
Paragraph
Page
4-1
Special Tools, TMDE and Support Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-1
4-2
Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .4-1
4-1. Special Tools, TMDE and Support Equipment. No special tools are required for unit maintenance
of the FARE. TMDE and support equipment are listed in the Maintenance Allocation Chart (MAC).
4-2. Repair parts. Repair parts required for maintenance of the FARE are listed in the Repair Parts and Special
Tools List (RPSTL), Appendix F of this manual.
Section II. SERVICE UPON RECEIPT
Paragraph
Page
4-3
Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...4-2
4-4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 4-2
4-5
Inspection and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 4-2
4-1
|
