TM 10-4320-342-24 LEGEND FOR FIGURE FO-2 ITEM DESCRIPTION A-1 Starter/Generator: Start: 28 volts DC, 1000 amps Operating: 30 volts DC, 6 kilowatts, 200 amps, 7,050 to 12,000 rpm A-3 Battery Tray B1 Winch Motor, 24 volts de, 1/2 horsepower BT1 Battery, 24 volts de, 30AH/1HR/800F/18V CB1 Circuit Breaker, Main 15 amps CB2 Circuit Breaker, Battery Heater, 50 amps CB3 Circuit Breaker, Sensing, 5 amps CB4 Circuit Breaker, Generator, 35 amps DS1 Light, Clutch Disengaged DS2 Light, Engine Oil Temperature DS3 Light, Engine (APU) Failure DS4 Light, Control Panel, 30 volts, 75 watts DS5 Light, Control Panel, 30 volts, 75 watts DS6 Light, Control Panel, 30 volts, 75 watts DS7 Light, Control Panel, 30 volts, 75 watts DS8 Light, Control Panel, 30 volts, 75 watts DS9 Light, Control Panel, 30 volts, 75 watts DS10 Light, Control Panel, 30 volts, 75 watts DS11 Light, Control Panel, 30 volts, 75 watts DS12 Light, Control Panel, 30 volts, 75 watts DS13 Light, Control Panel, 30 volts, 75 watts E-1 Ground Stud ESU Electronic Sequencing Unit F1 Fuse, 130 volts, 80 amps, slow acting HR1 Heater, Battery, 28 volt dc, 75 watts HR2 Fuel Line Heater, 24 volts dc, 50 watts HR3 Fuel Line Heater, 24 volts dc, 50 watts HR4 Fuel Line Heater, 24 volts dc, 50 watts HRS Fuel Line Heater, 24 volts dc, 50 watts J1 Connector, Control Box J2 Connector, Control Box J3 Connector, Control Box J4 Connector, Control Box J5 Connector, Clutch Assembly J9 Connector, Ejector solenoid J11 Connector, Battery J12 Connector, Battery Heater/Thermostat J13 Connector, Slave Receptacle K1 Relay, Main Power (S2, S4 and S6) Circuit K2 Relay, Charging Circuit K3 Relay, Engine Start and Starter/Generator Circuit K4 Relay, Electronic Sequencing Unit/95% Circuit K5 Relay, 3 Second Delay, Clutch Holding Circuit K6 Relay, Battery Heater Circuit K7 Relay, 3 Second Delay, Clutch Circuit K8 Relay, Winch Circuit, 24 volts, dc, normally open, 100 amps ITEM DESCRIPTION K9 Relay, Winch Circuit, 24 volts, dc, normally open, 100 amps K11 Relay, Pump Pressure Switch Circuit K12 Relay, Winch Circuit, 24 volts dc, normally closed, 200 amps L1 Clutch Assembly, 600 GPM, 6 volts dc, 1.076 ohms, 8000   500 rpm L2 Solenoid, Ejector, 24 volts DC, 0-60 psi L3 Solenoid, Drain, 24 volts, 11.2 watts, 40 psi L4 Pump Pressure Switch, 24 volts, DC, 5 amps, 20 psi L5 Fuel Pump, 24 volts DC, 3.25 amps, 20 psi, 40 gph L6 Gearbox Pump, 24 volts DC, 3.25 amps, 20 psi, 40 gph L7 Fuel Line Heater (HR2), 24 volts de, 50 watts L8 Gearbox Pump, 24  volts DC, 3.25 amps, 20 psi, 40 gph L9 Fuel Line Heater (HR3), 24 volts dc, 50 watts L10 Fuel Line Heater (HR4), 24 volts dc, 50 watts L11 Fuel Line Heater (HR5), 24 volts de, 50 watts M4 Ammeter, -10/0/+20 amps P1 Connector Plug, Control Box P2 Connector Plug, Control Box P3 Connector Plug, Control Box P4 Connector Plug, Control Box P5 Connector Plug, Clutch Assembly P6 Connector Plug, Pump Pressure Switch P7 Connector Plug, Boost Pump (Fuel Pump) P8 Connector Plug, Boost Pump (Gearbox) P9 Connector Plug, Ejector Solenoid P10 Connector Plug, Voltage Regular P11 Connector Plug, Battery P12 Connector Plug, Battery Heater/Thermostat P14 Connector Plug, Electronic Sequencing Unit P15 Connector Plug, Boost Pump (Gearbox) R1 Resistor, 3.3 ohms, 75 watts R2 Resistor, 1.8 ohms, 75 watts R3 Resistor, 15 ohms, 180 watts R4 Resistor, Shunt, 20 amps S1 Switch, Master S2 Switch, Fuel Heater S3 Switch, Engine Pumps S4 Switch, Start S5 Switch, Control Panel Lights S6 Switch, Pump Clutch S7 Switch, Remote Winch Controller S8 Switch, Remote Winch Controller TB1 Terminal Board, Control Box TB2 Terminal Board, Control Box TB3 Terminal Board, Control Box TB4 Terminal Board, Winch Enclosure TB5 Terminal Board, Heaters TS1 Thermostat, Battery, 120 volts, 1,500 watts, shutoff +230°F (112C) VR Voltage Regulator, 25-31 volts, 10 amps continuous, 15 amps overload Figure FO-2.  600 GPM Pump Wiring Diagram (Sheet 3 of 3) FP-11/(FP-12 Blank)