|
| |
T M 9 - 2 8 0 5 - 2 6 2 - 2 4P
N A V F A C P - 8 - 6 1 3 E - 2 4P
T O - 3 8 G 2 - 9 0 - 14
S L - 4 - 0 3 5 2 2C
b. (ALL) When National Stock Number or reference number is known:
(1) Using the Index of National Stock Numbers and Reference Numbers, find the pertinent National
Stock Number or reference number. This index is in ascending NSN sequence followed by a list of reference
numbers in alphanumeric sequence, cross–referenced to the illustration figure number and item number.
(2) After finding the figure and item number, locate the figure and item number in the repair parts list.
6. (F) Use of the Reference Designator Index Section.
This Section (section V) is used when the reference designator is known or identified by other technical
manuals supporting this equipment. The reference number is given in this Section. If description or location is
desired, note the figure and item number. Turn to Section II to the noted figure and item number. The location
of the part and description is given in this listing (Not Applicable).
7. Abbreviations.
ALUM . . . . . . . . . . . . . . . . . . . . .. aluminum
ANPT . . . . . . . . . . . . . . . . . . . . . . aeronautical national taper pipe threads.
CAD . . . . . . . . . . . . . . . . . . . . . ..cadium
EA . . . . . . . . . . . . . . . . . . . . . . . .. each
EXT . . . . . . . . . . . . . . . . . . . . . . .. external
FWD ... . . . . . . . . . . . . . . . . . . .. forward
HEX . . . . . . . . . . . . . . . . . . . . . . . hexagon
HP . . . . . . . . . . . . . . . . . . . . . . . . . horsepower
ID . . . . . . . . . . . . . . . . . . . . . . . . . inside diameter(s)
IN . . . . . . . . . . . . . . . . . . . . . . . . . inch(es)
LG . . . . . . . . . . . . . . . . . . . . . . . . . length (long)
MIL-STD . . . . . . . . . . . . . . . . . . . . military standard
MM . . . . . . . . . . . . . . . . . . . . . . . . millimeter(s)
MTG . . . . . . . . . . . . . . . . . . . . . . . mounting(s)
NOM . . . . . . . . . . . . . . . . . . . . . .. nominal
NPTF . . . . . . . . . . . . . . . . . . . . . . national taper pipe (thread) fine
OD . . . . . . . . . . . . . . . . . . . . . . . . outside diameter(s)
THK . . . . . . . . . . . . . . . . . . . . . . . . thick(ness)
UNF . . . . . . . . . . . . . . . . . . . . . ..unified fine thread
8. Federal Supply Codes for Manufacturers
C o de
Manufacturer
7
7
2
60
Pierce Govenor Co.,
P.O. Box 2000
Cupland, IN 46989
Inc.,
8
0
2
05
National Aerospace Standards Committee
Industries Association of America, Inc.
1725 Desales NW Washington, D.C. 20036
8
1
3
48
Federal Specifications Promulgated by General Services Administration,
Washington, D.C. 20001
8
1
3
49
8
1
3
52
8
Military Specifications Promulgated by Military Dept’s/Agencies under Authority of Defenses
Standardization Manual 4120–3–M
Air Force – Navy Aeronautical Specifications Promulgated by Aeronautical Standards Group
|
