| |
- DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL PUMP, CENTRIFUGAL, SELF-PRIMING, GASOLINE ENGINE DRIVEN, WHEEL MOUNTED, 6-INCH, 1500 GPM CAPACITY AT 60 FOOT HEAD
- WARNING
- Table of Contents
- LIST OF ILLUSTRATIONS
- LIST OF ILLUSTRATIONS-continued
- CHAPTER 1. INTRODUCTION
- Figure 1-1. Centrifugal pump, left rear view.
- Figure 1-2. Centrifugal pump, right front view.
- Tabulated Data
- Table 1-1. Tabulated Data-continued
- Table 1-1. Tabulated Data-continued
- CHAPTER 2. DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- Figure 2-1. Cylinder head.
- Table 2-1. Troubleshooting-continued
- Figure 2-3. Compression test.
- COMPRESSION TEST-continued
- Figure 2-4. Valve adjustment.
- WATER TEMPERATURE SAFETY SWITCH STOPS ENGINE OPERATION
- Figure 2-5. Radiator removal.
- Figure 2-6. Oil pressure adjustment
- Figure 2-7. Governor adjustment.
- Figure 2-8. Carburetor removal.
- Figure 2-9. Magneto removal.
- Figure 2-10. Governor removal.
- Figure 2.11. Engine timing marks.
- Figure 2-12. Engine timing mark pointer.
- Figure 2-13. Magneto-to-spark plug connections.
- Figure 2-14. Centrifugal pump removal and installation.
- PUMP RUNS WITH NO DISCHARGE OR WITH LOW PRESSURE-continued
- Figure 2-15. Centrifugal pump disassembly and reassembly.
- CENTRIFUGAL PUMP-continued
- Figure 2-16. Centrifugal pump removal and installation.
- CENTRIFUGAL PUMP-continued
- Figure 2-17. Centrifugal pump disassembly and reassembly.
- PUMP MAKES EXCESSIVE NOISE
- Figure 2-18. Centrifugal pump removal and installation.
- Figure 2-19. Pump coupling.
- Figure 2-20. Bearing housing.
- Section III. GENERAL MAINTENANCE
- Section IV. REMOVAL AND INSTALLATION OF MAJOR COMPONENTS AND ASSEMBLIES
- Figure 2-21. Centrifugal pump, removal and installation.
- Flexible Coupling
- Figure 2-22. Pump coupling, exploded view
- Engine
- Figure 2-23. Engine, removal and installation
- CHAPTER 3. REPAIR OF ENGINE COMPONENTS
- Figure 3-1. Operation of engine speed regulating system.
- Cleaning and Inspection
- Section III. REPAIR OF RADIATOR
- Engine Oil Filter
- Figure 3-4. Engine oil filter mounting, exploded view.
- Engine Oil Pressure Adjustment
- Section V. REPAIR OF ELECTRICAL SYSTEM COMPONENTS
- Figure 3-7. Alternator assembly, exploded view.
- Figure 3-8. Alternator brush assembly, showing continuity paths.
- Testing.
- Figure 3-9. Stator winding and connections.
- Figure 3-10. Stator test points.
- Figure 3-11. Alternator bench test circuit.
- Starting Motor
- Figure 3-13. Circuit for checking pinion clearance.
- Figure 3-15. Starting motor, exploded view.
- Figure 3-16. Starting motor no-load test setup.
- Radio Interference Suppression
- Section VI. REPAIR OF ENGINE MOUNTING
- Cleaning and Inspection.
- CHAPTER 4. REPAIR OF ENGINE
- Table 4-1. Engine fits, tolerances, and wear limits-continued
- Table 4-1. Engine fits, tolerances, and wear limits-continued
- Figure 4-1. Cylinder head, exploded view.
- Intake and Exhaust Valves
- Figure 4-3. Valves and camshaft, exploded view.
- Figure 4-4. Valve guide installation dimensions.
- Figure 4-5. Narrowing valve seat.
- Figure 4-6. Oil pan and filler blocks, exploded view.
- Engine Oil Pump
- Flywheel and Flywheel Housing
- Figure 4-9. Checking flywheel runout.
- Pistons and Connecting Rods
- Figure 4-13. Piston, crankshaft, and flywheel, exploded view.
- Figure 4-14. Checking piston fit in cylinder bore.
- Main Bearings and Crankshaft
- Figure 4-15. Removing upper bearing shell with angular pin.
- Figure 4-16. Checking bearing clearance with plastigage.
- Camshaft.
- Cylinder Block
- Removal and Disassembly-continued
- Cleaning
- CHAPTER 5. REPAIR OF CENTRIFUGAL PUMP ASSEMBLY
- Figure 5-1. Centrifugal pump, exploded view.
- Centrifugal Pump Overhaul
- Bearing Housing
- Pump Performance Test
- CHAPTER 6. REPAIR OF CHASSIS
- Figure 6-1. Axle and suspension system, exploded view.
- Chassis Frame
- Figure 6-2. Chassis frame, exploded view.
- Cleaning and Inspection.
- APPENDIX A. REFERENCES
- INDEX
- INDEX-continued
- INDEX-continued
- INDEX-continued
- INDEX-continued
- Blank Page
- TM-5-4320-234-34
- Shared Top Border
- Distribution
- Shared Bottom Border
- RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
- Shared Left Border
|