 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 5-4320-222-25P
i.
One-Year
Allowances
Per
100
Equip-
sity column to obtain the total quantity of re- pair parts
ments/Contingency Planning Purposes. Indicates the
authorized.
(3) Organizational units providing maintenance for
quantity required for distribution and contingency
more than 100 of these equipment's shall determine 'the
planning purposes. The range of Items indicates total
total quantity of parts required -by converting the
quantities of all authorized items required to provide for
equipment quantity to a decimal factor by placing a
adequate support .of 100 equipment's for one year.
Depot Maintenance Allowance Per 100
decimal point before the next to last digit of the number
j.
Equipment's. Indicates the quantity authorized for depot
to indicate hundredths, and multiplying the decimal
factor by the parts quantity authorized in the 51-10'0
maintenance of 100 equipment's. Items authorized for
allowance column. Example, authorized allowance for
use but not for initial stockage are identified with an
51-100 equipment's is 12; for 140 equipment's multiply
asterisk in the allowance column.
k. Illustration.
12 by 1.40 or 16.80 rounded off to 17 parts required.
(1) Figure Number. Indicates the figure number of
(4) Subsequent changes to allowances will be
limited as follows: No change in the range of items is
the illustration in which the item is shown.
authorized.
If additional items are considered
(2) Item Number. Indicates the callout number
necessary, recommenda- tion should be forwarded to U.
used to reference the item In the illustration.
S. Army Mobility Equipment Command for exception or
revision to the allowance list. Revisions to the range of
4. Special Information
items authorized will be made by this Command based
a. Repair parts mortality has been based on 1, 000
upon engineering experience, demand data, or TAE)RS
hours of operation per year.
information
b. Parts which require manufacture or assembly at a
category higher than that authorized for installation will
h. Thirty-Day DS/GS Maintenance Allowances.
indicate In the source column the higher category.
c. The following publications pertain to the pump and
(1) The allowance columns are divided into three
, its components: For repair parts and special tools , for
subcolumns. Indicated in each sub- column is the
the MIL STD Engine 2A016-II refer to TM 5-2805-206-
quantity of items authorized for the number of
24P
equipment's supported. Items authorized for use as
required but not for initial s'tockage are identified with an
5. How to Locate Repair Parts
asterisk in the allowance column.
a. W-hen Federal stock number or reference number
(2) The quantitative allowances for DS/ GS levels of
is unknown:
maintenance will 'represent initial stockage for a 30-day
(1) First. Using the table of contents, determine
.period for the number of equipment's supported.
the functional group within which the repair part belongs.
(3) Determination of the total quantity of parts
(2) Second. Find the illustration covering the
required for maintenance of more than 100 of these
functional group to which the repair part belongs.
equipment's can be accomplished by converting 'the
(3) Third. Identify the repair part on the illustration,
equipment quantity to a decimal factor by placing a
and note the illustration figure' and item number of the
decimal point before the next to last digit of the number
repair part.
to indicate hundredths, and multiplying the decimal
(4) Fourth. Using the repair parts listing, find the
factor by the parts quantity authorized In the 51-100
functional group to which the repair part belongs and
allowance column. Example, authorized allowance for
locate the illustration figure and Item number noted on
51-100 equipment's is 40; for 150 equipment's multiply
the illustration
40
by
1.50
or
60
parts
required.
v
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals