Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: RIGHT CABINET DOOR
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

TM   10-6630-247-13&P 4-16. CABINET REPAIR - cont.   (57) (58) (59) (60) (61) (62) Apply  adhesive  to  bottom  of  divider  (4).  Position  divider  (4)  in  cabinet  door  (21).  Make sure  cut-out  in  divider  is  positioned  as  shown, Apply  adhesive  to  left,  right  and  rear  edges  of  divider  (2). Apply  adhesive  to  both  ends  of  pipe  support  (3).  Position  pipe  support  on  divider  (4). Position  divider  (2)  in  cabinet  door  (21)  and  press  divider  onto  pipe  support  (3).  Make  sure cutout  in  divider  is  positioned  as  shown. Using No. 42 (3/32) drill bit, drill pilot holes into dividers (2 and 5) using holes in cabinet door (21) as a template. Install  four  screws  (1)  in  cabinet  door  (21). RIGHT CABINET DOOR. Cabinet  Retainers  and  Foam.  Refer  to  figure  4-17. (63) (64) (65) (66) (67) (68) (69) Apply  adhesive  to  back  of  foam  block  (11).  Position  foam  block  in  cabinet  door  (12)  and press in place. Apply  adhesive  to  foam  sheet  (10).  Position  foam  sheet  in  cabinet  door  (12)  and  press  in place. Apply  adhesive  to  foam  block  (9).  Position  foam  block  in  cabinet  door  (12)  and  press  in place. Position  door  (8)  on  cabinet  door  (12).  Using  No.  42  (3/32)  drill  bit,  drill  pilot  holes  into cabinet door (12) using hinge on door (8) as a template. Secure door (8) in place with three screws  (7). Position  retainer  (6)  on  cabinet  door  (12).  Using  No.  42  (3/32)  drill  bit,  drill  pilot  holes  into cabinet  door  using  hinge  on  retainer  as  a  template.  Secure  retainer  in  place  with  two screws  (5). Position  retainer  (4)  on  cabinet  door  (12).  Using  No.  42  (3/32)  drill  bit,  drill  pilot  holes  into cabinet door using hinge on retainer as a template. Secure retainer in place with two screws  (3). Position  retainer  (2)  on  cabinet  door  (12).  Using  No.  42  (3/32)  drill  bit,  drill  pilot  holes  into cabinet  door  using  hinge  on  retainer  as  a  template.  Secure  retainer  in  place  with  two screws  (1). f. Adjustment.  Refer  to  figure  4-15. (a) If panel (12) will not latch on cabinet door (21) (panel too tight), adjust two nuts (1 and 5) to move catch (3) upon stem of latch (7), then tighten two nuts. 4-43

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business