Quantcast Attaching Hoselines to Pumping Assembly

Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Attaching Hoselines to Pumping Assembly
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Laying    out    hoseline
Up
TM-10-3835-219-14 Hoseline Outfit Fuel Handling 4-Inch Diameter Manual
Next
Figure 2-5. Attaching Suction Hoseline to Pumping Assembly.
T M    1 0 - 3 8 3 5 - 2 1 9 - 14 N  O  T  E Adjust    lay-line    stripe    on    hose    when    coupling    hoselines    together. (e)  Couple   subsequent   truckloads   of   hose   to   existing   hoseline   section   using   coupling   procedure   in paragraph   h.   Noting   that   the   trailing   end   of   existing   hoseline   section   is   one   the   ground   and   the leading   end   of   new   hoseline   section   is   in   the   top   flaking   box   of   the   truck. 2 - 7 .   A t t a c h i n g     H o s e l i n e s     t o     P u m p i n g     A s s e m b l y . a. Attaching   Suction   Hoseline   to   Pumping   Assembly.   (figure   2-5) (1) (2) (3) (4) (5) (6) (7) (8) (9) ( l 0) (11) (12) (13) (14) Open   chest   containing   hoseline   flow   control   kit. Remove   one   coupling   half   quick   disconnect   (MALE)   (1). Remove   one   grooved-to-internal   thread   coupling   (2). Wrap   one   layer   of   white   teflon   tape   (3)   on   threads   of   each   coupling   half   quick   disconnect   (MALE)   (1). Screw   one   coupling   half   (1)   into   a   grooved-to-internal   thread   coupling   (2).   Coupling   must   be   tight   to prevent    leakage. Slide   pipe   coupling   clamp   rubber   gasket   (4)   over   end   of   hoseline   (5).   Make   certain   gasket   is   flush   with e n d. Place   grooved   adapter   (2)   in   line   with   hoseline   (5)   and   slide   gasket   (4)   over   joint.   Center   gasket   in   place. Place   lower   pipe   coupling   clamp   half   (6)   over   gasket,   then   position   upper   pipe   coupling   clamp   half   (7). install   two   bolts   (8),   and   nuts   (9)   so   that   nuts   (9)   will   be   exposed   on   the   upper   coupling   half   (7). Hand   tighten   nuts   (9)   evenly,   then   with   wrench,   tighten   nuts   evenly   until   coupling   faces   meet. Continue   tightening   nuts   evenly,   until   both   bolts   are   secure. Remove   one   plug   (10)   at   suction   port   (11)   of   pump.   Ensure   that   gasket   is   properly   positioned   in   pump coupling    half. Attach   hoseline   (5)   to   pump   suction   port   (11). Secure   coupling   (1)   with   pump   coupling   half   cam-lock   lever   (12). Repeat   steps   1   through   13   if   a   second   hoseline   is   required. 2 - 2 1

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business