Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Flow Control Kit Chest Assembly
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

T M  1 0 - 3 8 3 5 - 2 1 9 - 1 4 5-6.  Flow   Control   Kit   Chest   Assembly. This   task   consists   of: Repair INITIAL   SET-UP Tools M a t e r i a l s / P a r t s ( c o n t) Drill   (Appendix   B,   Section   Ill,   Item   2) Rivets   (Refer   to   TM   10-3835-219-24P) Riveter   (Appendix   B,   Section   Ill,   Item   3) E q u i p m e n t      C o n d i t i on M a t e r i a l s / P a r ts Kit   components   removed   (para   3-7) Solvent,   Dry   Cleaning   (Item   7,   Appendix   E) Rags,   Wiping   (Item   5,   Appendix   E) r   (figure   5-2) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) 5-6 NOTE The   flow   control   kit   chest   assembly   is   made   up   of   three   chest   assemblies. One   chest   assembly   for   Model   ADC-1200   and   two   chest   assemblies   for Model   1461.   Components   of   the   flow   control   kit   for   Model   FIHK-100   are contained   in   one   chest   assembly.   The   size   of   each   chest   assembly   varies. The   repair   of   each   chest   assembly   is   the   same. Inspect   all   components   and   chest   assembly   and   replace   if   damaged. Drill   out   rivets   (1)   on   each   side   of   chest   and   disconnect   lid   supports   (2). While   supporting   lid   (3),   drill   out   rivets   (7)   attaching   hinge   (5)   to   chest   (6)   and   remove   lid. Place   lid   (3)   on   bench   and   drill   out   rivets   (7)   attaching   hinge   (5)   to   lid   (3). Drill   out   rivets   (8)   on   each   side   of   lid   and   disconnect   lid   support   (2)   from   lid   (3)   and   remove s u p p o r t. Drill   out   rivets   (9)   attaching   handles   (10)   to   chest   (6)   and   remove   handles. Drill   out   rivets   (11)   attaching   lower   latch   half   (12)   to   chest   (6)   and   remove   latch   half. Drill   out   rivets   (13)   attaching   upper   latch   half   (14)   to   lid   (3)   and   remove   latch   half. Weld   any   cracks,   breaks   or   holes   in   chest   (6)   and   partitions   (15) W A R N I NG Dry   cleaning   solvent   used   to   clean   parts   is   potentially   dangerous   to personnel    and    property.    Avoid    repeated    and    prolonged    skin    contact. Do   not   use   near   open   flame   or   excessive   heat.   Flash   point   of   solvent   is 100°F-138°F(38°C-60°C). Clean   all   items   with   dry   cleaning   solvent,   and   dry   thoroughly. Change   1

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business